X-PROG 3

The X-PROG 3 key and immobilizer programmer is a powerful anti-theft solution and an ideal choice for professional repair shops and vehicle maintenance businesses. X-PROG 3 is an integrated multi-function module, which offers multiple functions in one device for fast and accurate reading and writing of data. With powerful functions, supporting Mercedes-Benz infrared key reading / writing, BMW engine ISN code reading, engine reading in BENCH mode, etc. X-PROG 3 is flexible, stable, reliable, and suitable for professional users.

Technical Data

Interface
DB26, DB15

Input Voltage
DC 12 V

Input Current
500 mA

Working Temperature
0 - 15 °C

Storage Temperature
- 20 - 70 °C

Dimensions
39 x 107 x 298 mm

Features

Anto-Theft Type
Identification

Remote Control Matching

Key Chip
Read & Write

Anti-Theft Password Reading

Anti-Theft Component Replacement

HD Box 3

The new LAUNCH HD Box 3 is the perfect expansion module for users of the X-431 EURO PRO 4 and X-431 EURO PRO 5. Trucks, buses and commercial vehicles from over 20 manufacturers are covered. Communication is established via Bluetooth or by cable and supports 12 V and 24 V on-board voltage.

Technical Data

Operating Voltage
DC 9 - 36 V

Test Voltage
DC 12 V

Power Input
≤ 3 W

WLAN

USB

Bluetooth

Working Temperature
- 10° C ~ 50° C

Dimensions
264 x 210 x 30 mm

Features

Supports over 20 Manufacturers

Online Update

ABS Control Unit

Service Functions

Time Maintenance

Transmission Reset

Engine Reset

Retardar Reset

Oil Reset

Read AdBlue Status and Consumption

Setting Vehicle Speed Limit

Setting Vehicle Rotational Speed

Fuel Consumption Setting

Non-Standard Connector Pack

Non-standard connector pack allows X-431 LITE version device to diagnose old vehicles with a non OBD II socket, the pack consists of 24 connectors for different vehicle models.

HD Pack

HD Pack for EURO TAB II consists of activation code for HD Software and non-standard HD cables. The Smartbox 3.0 which comes with the X-431 EURO TAB II is compatible with both 12 V and 24 V.

O2-1 ScopeBox

Turn your X-431 EURO TAB II into a 4-channel oscilloscope with the help of the LAUNCH O2-1 ScopeBox. The ScopeBox captures faulty / irregular signals for curve analysis on the screen of the X-431 EURO TAB II. This analysis can be used to detect various defects, e.g. in sensors, actuators and circuits. Gain valuable time in vehicle diagnostics and save costs for unnecessarily replaced components.

Previous
Next

Technical Data

Channels
1 GB for 4 Channels

DC Accuracy
DC Gain
± 3 %

Bandwidth
100 MHz

Rise Time
± 3.5 ns (typical)

Sampling Rate
1 GB for 4 Channels

Input Impedance
1 MΩ ± 1.5 %

Memory Depth
50 M for 4 Channels

Vertical Resolution
8 bit

Vertical Scale
5 mV ~ 10 V

Vertical Offset Range
± 2.5 V ± 120 V

Invert
Support

Coupling
DC, AC

Time Base
50 ns ~ 1 ks

Time Base Precision
20 ppm

Features

Automatic Measurement
23 Arten

Powerful Trigger Function

High Memory Depth

Special Quick Memory Function

Virtual
Keyboard

Several System Settings

Waveform Recording

Scopebox

Turn your diagnostic device into a 4-channel oscilloscope with the help of the LAUNCH Scopebox. The Scopebox captures faulty / irregular signals for curve analysis. This analysis can be used to detect various defects, e.g. in sensors, actuators, circuits and control units. Gain valuable time in vehicle diagnostics and save costs for unnecessarily replaced components.

Technical Data

Scanning Frequency
4 Channel up to 200 MHz

DC Precision
± 1 %

Bandwidth
20 MHz

USB

Features

Recording and storage of the signal curves

Automatic Adjustmenr on
4 Channels

Fast Detection of Interference Pulses

Simple to Use

S-2 Sensorbox

The S2-2 Sensor Box is specially designed for the diagnosis and simulation of sensor faults. It mainly contains “Sensor”, ” Actuator”, “Defined / Draw”, “Timing Waveform” and ” Multimeter”. The module cannot be used separately, but must be operated together with LAUNCH-specific diagnostic tools that are compatible with this module.

Technical Data Sensorbox

Channels
2 Channels

Accuracy
± 1 %

Amplitude Range
0 V - 20 V

Max. Current Output
20 mA

Predefined Frequency Range
0 - 20 kHz

Square Wave Signal Frequency Range
0 - 15 kHz

Duty Cycle of the Square Wave Signal
0 - 100 %

Power Supply
Simulator Sensor Output Max. 20 mA

DC Voltage Simulation
supported

Fixed Frequency Simulation
supported

Predefined Wave Simulation
supported

Predefined Frequency Range
supported

Signal Generator Interface
2 Interfaces

External Power Supply
1 Connector

Magnetic Interface
1 Interface

Multimeter Interface
2 Interfaces

Operating Temperature
0°C - 50°C

Storage Temperature
-30°C - 70°C

Predefined Frequency Range
0 - 20 kHz

Predefined Frequency Range
supported

Storage Temperature
-30°C - 70°C

Technical Data Multimeter

DC /VC Voltage

Resistance Test
0 - 40 MΩ

Capacity
0 F - 100 uF
(max. 30 s Measuring Time)

Diodes
0 V - 1.5 V

Continuity Detection
Noises below 30 MΩ

Features

Hand-Drawn Curve Progression on Screen

Sensor Simulation
DC Voltage, Fixed Frequency, Predefined Curve Progression

Integrated Multimeter Test Function
Electric Voltage, Resistance, Frequency

Sensorbox

Turn your X-431 EURO TAB II into a sensor simulator with the help of the Sensorbox. Can’t tell for sure whether sensors are defective? Simply simulate target curves using the Sensorbox and make sure! Do you need a slightly different shape of the curve? No problem, just draw the curve by hand on the display of the X-431 EURO TAB II and the Sensorbox will generate the desired curve. The Sensorbox also makes it possible to generate and modify all kinds of signal parameters, such as: Coolant temperature, mass air flow, throttle position and many more. Save yourself the time of having to readjust certain situations during test drives!

Technical Data

Accuracy
± 5 %

Amplitude Range
- 12 V up to + 12 V

Max. Power Output
20 mA

Predefined Frequency Range
0 up to 150 Hz

Square Wave Signal Frequency Range
0 up to 15 kHz

Technical Data Multimeter

Accuracy
± 5 %

Voltage Test
- 400 up to + 400
Input Resistance: 10 MΩ

Resistance Test
0 up to 10 MΩ

Frequency Test
0 up to 25 kHz
Input Resistance: 1.000 MΩ
Output Resistance: 1V bis 12 V

Features

Hand-Marked Curve

Sensor Simulation
DC Voltage, Fixed Frequency, Predefined Curve Progression

Integrated Multimeter Test Function
Electr. Voltage, Resistance, Frequency

VSP-808 Videoscope

VSP-808 Videoscope

The VSP-808 is a professional video endoscope that displays a real-time view of the vehicle’s internal structure on a 4.3″ TFT display and stores images. The visible pre- and post-inspection process greatly improves customer satisfaction.

Technical Data

Display
4.3" TFT
480 x 272 RGB

Battery
1.800 mAh
3.7 V Li-on

Resolution Probe
1.280 x 720
720 p

Sensor Size Probe
2,8 mm
CMOS 720 p

Frame Rate Probe
30 fsp

Focus Frequency Probe
3 - 300 mm

Cable Length Probe
1.000 mm

Memory
8 MB

Probe Ø
5,5 mm

Cable Ø
4,8 mm

Arbeitstemperatur
- 20 °C bis 60 °C

Features

Fast Image Capturing

Display and Save Pictures

Built-in memory can store up to 150 images

Light source: 6 dimmable LEDs for optimal illumination.

1 m probe cable
abrasion resistant and solid

Probe button and probe cable IP6

VSP-600 USB
Videoscope

The LAUNCH video endoscope is the ideal tool for viewing and capturing video and images in hard-to-reach areas of your vehicle. Equipped with a 7 mm small and fluid-resistant camera head and adjustable LED illumination.

LAUNCH-EUROPE-Diagnose-Zubehör-Videoscope

Technical Data

Diameter
5,5 mm

Sensor Size
1/9"

Temperature
- 10° C - 55° C

Resolution
1.280 x 720

USB
Type C micro USB

Power
5 V

LED
5 Level

Cable
4.8 Ø
Length 800 mm

Features

Fast Video and Image Recording

Viewing and Saving Images and Videos

Automatic White Balance

TIT-201

The TIT-201 is an infrared thermal imaging camera that measures surface temperature and displays live thermal images. With the help of infrared sensors and optical lenses, infrared radiation can be detected by the thermal imaging camera. The radiation is then converted into a clearly visible colour image and displayed on the screen. This fast and accurate method enables the user to find the heat source effectively, accurately and in a time-saving manner.

Technical Data

Display
3,2" TFT Display
240 x 320 px

Image Format
JPG

Memory
3 GB
up to 20.000 Images

Colour Palette
Rainbow, Iron Red, Cold Colour, Black
and White

Visible Light Camera
300.000 Pixel

Resolution of the Infrared Image
220 x 160 px

USB

Measuring Range
- 20 up to 450° C
- 4 up to 840° F

Battery
2.000 mAh

Features

5 Special Display Options

Infrared Image

Accuracy
up to 0,07°

Measuring Distance
0,5 - 40 m

Flashpower 120

Flashpower 120 is a high-performance battery charger with compact dimensions. It is suitable for use in workshops, by vehicle electronics technicians and car dealers for charging car batteries and ensuring the power supply for all types of programming, flashing and vehicle diagnostics.

Technical Data

Voltage
90 - 260 V

Performance
1.800 W

Output Voltage
12 V

Charging Current
10 - 120 A

Battery Selection
Wet-Cell Battery AGM
Lithium

Charge Capacity
10 - 1.200 Ah

Maintenance Capacity
10 - 3.600 Ah

Cable Length
Standard: 2,7 m
Optional: 6 m

Dimensions
350 x 450 x 150 mm

Weight
8,5 kg (2,7m Cable)
10,3 kg (6m Cable)

Features

Battery Charge

Battery Regeneration

Charging Time 8 Hours

Power Supply

PFP-100

PFP-100 is a professional 100 Ampere vehicle battery power support unit with high-performance, compact size and high-quality. It is used by garages, car electricians and car dealerships, mainly for supplying continuous power to the vehicles battery, during all stages of ECU reprogramming and flashing, according to the request of car OEMS.

Technical Data

Voltage
110 - 220 V

Performance
1.200 W

Output Voltage
12 V

Charging Current
2 - 16 V / 2 - 100 A

Battery Selection
Regulare, AGM, GEL

Charge Capacity
10 - 1.200 Ah

Maintenance Capacity
10 - 3.600 Ah

Cable Length
Standard: 3 m

Dimensions
430 x 350 x 140 mm

Weight
7,7 kg

Features

Battery Charge

Battery Regeneration

Charging Time 8 Hours

Power Supply

Trolley

Professional multifunction trolley for battery chargers, diagnostic equipment and much more. Ideal for use in the workshops, when programming control units on the vehicle, for example in combination with the new Flashpower 120. The multifunction trolley offers convenience and flexibility for daily work in the workshop.

Features

Dimensions
1.120 x 560 x 540 mm

Weight
25,5 kg

Ideal for Workshops

In Combination with Control Units

Pro Trolley TWT-100

Pro Trolley
TWT-100

TWT-100 is new professional multi-function trolley for diagnosis devices, battery chargers, oscilloscope, and much more, ideal to be used in the workshop during the vehicle’s ECU reprogramming in combination with the LAUNCH Flashpower product. It provides the convenience and flexibility for the daily work in a workshop. 4 layers and 1 lockable drawer are enough to hold all kinds of devices for vehicle diagnosis & ECU flashing. 4 universal wheels keeps it moving smoothly. The front and rear handles are designed to facilitate movements.

Features

Dimensions
1.300 x 670 x 610 mm

Weight
71 kg

Ideal for Workshops

In Combination with Control Units

Wi-Fi Printer

Print your fault codes and the corresponding descriptions as well as actual values, coding information and much more. In practical pocket format, it makes printing easy and blazingly fast. Can be combined with the EURO TAB II and EURO PRO 4 diagnostic devices.

Technical Data

Wi-Fi

Battery
Lithium Ion

Dimensions
124,5 x 79,3 x 35,3 mm

Features

Print Error Codes and more

Ergonomic, Light and Handy

Automatic Paper Feed

BST-860

The new BST-860 battery tester with integrated thermal printer is the ideal solution for testing 6 V, 12 V and 24 V batteries and their associated electrical systems.

Technical Data

Display
LCD Display

Measuring Cable
80 cm

Working Temperature
- 18 up to 50° C

Dimensions
188 x 95 x 41 mm

Weight
450 g